AQA A-Level Physics Unit 3 Mark Scheme (January 2022): Practical Skills and Exam Strategy | AQA A-Level 物理 Unit 3 评分方案（2022年1月）：实验技能与应试策略

📚 AQA A-Level Physics Unit 3 Mark Scheme (January 2022): Practical Skills and Exam Strategy | AQA A-Level 物理 Unit 3 评分方案（2022年1月）：实验技能与应试策略

AQA A-level Physics Unit 3, also called Paper 3, is the paper that tests your practical skills, data analysis and understanding of an optional topic. The January 2022 mark scheme is a powerful revision tool because it shows exactly how examiners award marks. It lists acceptable answers, common alternative phrasings and the scientific reasoning they reward.

AQA A-level 物理 Unit 3，也称为试卷3，主要考查实验技能、数据分析以及对选修专题的理解。2022年1月的评分方案是非常有效的复习工具，因为它清楚显示了考官如何给分：可接受的答案、常见的替代表述以及他们认可的推理过程。

1. Overview of Unit 3 and the Mark Scheme | Unit 3 与评分方案概览

The paper is divided into two sections. Section A covers practical skills: planning experiments, collecting data, drawing graphs, calculating uncertainties and evaluating methods. Section B covers your chosen optional topic, such as astrophysics, engineering physics or medical physics.

本试卷分为两部分。A 部分考查实验技能：设计实验、收集数据、画图、计算不确定度以及评价方法。B 部分考查你选择的选修专题，例如天体物理、工程物理或医学物理。

Section A questions often require short answers, calculations and graph work.

A 部分题目通常需要简答、计算和作图。
Section B questions reward recall of the optional topic as well as application to unfamiliar situations.

B 部分题目既考查选修专题的记忆，也考查在新情境中的应用。

Understanding the mark scheme helps you see that many marks are not for ‘correct final answers’ but for clear method, correct units and sensible use of significant figures.

理解评分方案能帮助你认识到：很多分数并不是给“最终正确答案”，而是给清晰的方法、正确的单位和合理的有效数字。

2. How the Mark Scheme Allocates Marks | 评分方案如何分配分数

Each mark is usually called a ‘mark point’. A question may have several acceptable answers, and the mark scheme will say ‘accept’ or ‘allow’. This means a slightly different but scientifically valid answer can still gain full marks.

每个分数通常称为一个“得分点”。一道题可能有好几个可接受的答案，评分方案中会写“accept”或“allow”，表示科学上合理但表述稍有不同的答案也能得满分。

Independent marks: one invalid point does not cancel another valid point.

独立计分：一个无效的要点不会抵消另一个有效要点。
Error carried forward (ecf): a later calculation using your earlier wrong value can still be credited.

错误后延（ecf）：你后面的计算如果正确使用了前面错误的数值，仍然可以获得分数。
Units and significant figures: mark schemes often award a separate mark for consistent units or an appropriate number of significant figures.

单位和有效数字：评分方案通常为一致的单位或合适的有效数字单独给分。

In January 2022, examiners noted that many students lost marks because they wrote a final answer without a unit. Always check whether the mark scheme shows units in the answer line.

2022年1月的报告中提到，许多学生因最终答案没有写单位而失分。务必检查评分方案答案行中是否包含单位。

3. Command Words and What They Require | 指令词及其要求

The mark scheme rewards answers that match the command word. Using the wrong style, such as writing an explanation when the question asks you to ‘state’, wastes time.

评分方案只奖励符合指令词要求的答案。如果题目要求“state（陈述）”，你却写了一大段解释，就会浪费时间。

Command word	What the examiner expects	中文要求
State	A single word, value or formula. No explanation is needed.	只需给出一个词、数值或公式，无需解释。
Determine	A calculation or graph reading with a final answer and unit.	需要通过计算或读图得到最终答案，并写出单位。
Show that	Write enough working to verify a given value.	写出足够过程，以验证题目给出的数值。
Explain	Give reasoning, often using physics principles.	需要说明原因，通常要利用物理原理。
Suggest	A plausible answer is accepted, often from outside taught material.	接受合理答案，有时需要运用课外的常识。

You should match the level of detail to the number of marks. A 2-mark ‘explain’ question usually needs a cause and an effect statement.

你要根据分数调整详细程度。一个2分的“explain”题通常需要写出“原因”和“结果”两个层次。

4. Experimental Setup and Measurement Precision | 实验装置与测量精度

Section A regularly asks about the choice of measuring instrument and how to reduce random and systematic errors. In January 2022, mark schemes rewarded answers that mentioned the resolution of the instrument explicitly.

A 部分经常考查测量仪器的选择以及如何减小随机误差和系统误差。2022年1月的评分方案对明确提到仪器分辨率的答案会给分。

Use a micrometre for thickness around a few millimetres, not a metre ruler.

测量几毫米的厚度应使用千分尺，而不是米尺。
Measure the period of a pendulum as time for 20 oscillations and divide by 20 to reduce random timing error.

测量单摆周期时，应测量20次全振动所用时间再除以20，以减小随机计时误差。
Use a data logger to record rapid changes more precisely than manual reading.

使用数据采集器记录快速变化，比手动读数精度更高。

In the mark scheme, a statement such as ‘the resolution of the stopwatch is 0.01 s, so the percentage uncertainty is small’ attracts the method mark.

在评分方案中，像“秒表的分辨率为0.01 s，因此百分比不确定度很小”这样的说法能获得方法分。

5. Presenting Data: Tables and Graphs | 数据呈现：表格与图线

Many experimental questions require you to present data in a table and plot a graph. The mark scheme for January 2022 gave credit for using a table heading with the symbol and unit divided by a slash, for example I / A.

许多实验题要求你以表格形式呈现数据，并绘制图线。2022年1月评分方案会对表格标题使用“符号 / 单位”的格式给分，例如 I / A。

Table headings should be written as ‘quantity / unit’, not with the unit in parentheses.

表格标题应写成“物理量 / 单位”，而不是把单位写在括号里。
All measured values in one column should have the same number of decimal places.

同一列测量值应保留相同的小数位数。
Axes should be labelled with ‘quantity / unit’ and use a scale that allows at least half the grid to be used.

坐标轴应标注“物理量 / 单位”，比例尺应使图线至少占用半页方格纸。

For graphs, the mark scheme often has separate marks for plotting, drawing the line of best fit and using the gradient.

对于图线，评分方案往往分别给描点、画最佳拟合线和利用斜率求值的分数。

6. Calculating Gradients and Uncertainties | 计算斜率与不确定度

A typical Unit 3 calculation asks you to determine the gradient of a straight-line graph. The gradient is found using two points on the line, not data points from the table.

Unit 3 的典型计算题要求你求直线的斜率。斜率必须在图线上取两个点来计算，而不是直接使用表格中的数据点。

m = Δy / Δx

You must show the coordinates you chose and substitute them clearly.

你必须写出所选点的坐标，并清楚代入公式。

Uncertainty in the gradient is found by drawing lines of maximum and minimum gradient that fit the error bars.

斜率的不确定度可以通过画出能经过误差棒的最大斜率线和最小斜率线来获得。

Δm = (m_max − m_min) / 2

In the mark scheme, you can score a mark even if your uncertainty is written as a value with one significant figure and the same unit as the gradient.

在评分方案中，只要你不确定度写成一位有效数字，并且单位与斜率相同，就可以得到分数。

7. Verifying Relationships Using Linearisation | 用线性化验证物理关系

Many equations are non-linear, but the mark scheme expects you to know the linear form. For example, the period of a simple pendulum is:

很多方程是非线性的，但评分方案希望你掌握其线性形式。例如，单摆周期公式为：

T = 2π√(l/g)

Squaring both sides gives a linear relationship when T² is plotted against l:

对方程两边平方，可得 T² 与 l 之间成线性关系：

T² = (4π²/g) l

If the graph of T² against l is a straight line through the origin, then T² is proportional to l, and the gradient equals 4π²/g. From this, you can calculate g.

如果画出 T² 对 l 的图线是一条过原点的直线，则说明 T² 与 l 成正比，斜率等于 4π²/g，由此可计算 g。

Alternative linearisation methods include using ln(T) against ln(l). The mark scheme accepts this if the working is consistent.

另一种线性化方法是画 ln(T) 对 ln(l) 的图线。只要过程一致，评分方案也会接受。

8. Evaluating Methods and Suggesting Improvements | 评价实验方法与提出改进

The final part of Section A often asks you to evaluate the experiment. The January 2022 mark scheme rewarded specific improvements rather than vague comments such as ‘be more careful’.

A 部分的最后通常要求你评价实验。2022年1月评分方案奖励具体的改进措施，而不是像“更小心一些”这样笼统的表述。

Add a fiducial marker, such as a vertical pin, to reduce parallax when timing the pendulum.

加一个基准标记，例如竖直的针，以减小计时单摆时的视差。
Start measuring after the system has reached a steady state rather than at the initial expansion.

在系统达到稳定状态后再开始测量，而不是在初始展开阶段开始。
Repeat measurements and calculate a mean to reduce random error.

重复测量并计算平均值，以减小随机误差。
Use a top-pan balance with a high resolution when measuring small masses.

测量小质量时，应使用分辨率较高的托盘天平。

Each improvement should be linked to a specific error. For example, ‘use a motion sensor to remove reaction-time error in the timing of the trolley’ gains a mark because it names the error and the improvement.

每条改进都应联系到具体误差。例如，“使用运动传感器以消除计时小车时的反应时间误差”能得分，因为它既点名误差又给出了改进方法。

9. Common Pitfalls in the January 2022 Paper | 2022年1月试卷常见失分点

Examiners reported that students repeatedly lost marks on the same types of mistakes. You can avoid these by reviewing the mark scheme’s most common notes.

考官报告指出，学生总是在同一类错误上反复失分。你可以通过复习评分方案中最常见的批注来避免这些问题。

Quoting readings to more significant figures than the instrument allows, such as writing 15.32 cm from a ruler that measures only to the nearest millimetre.

读数有效数字超出了仪器允许范围，例如用毫米刻度尺却记成 15.32 cm。
Forgetting to include both a unit and a sign for values such as displacement or potential difference.

例如位移或电势差等物理量忘记写单位或正负号。
Drawing the line of best fit through all plotted points instead of balancing points above and below the line.

让最佳拟合线强行穿过所有描点，而不是让点均匀分布在线的上下两侧。
Using the origin as a data point when it was not measured in the experiment.

把原点当作实验测量点来使用，但实验中并未测量原点坐标。

If the mark scheme says ‘allow a horizontal line’, it means you do not need to force a curved fit through every point: the physics may suggest a constant value.

如果评分方案写“allow a horizontal line”，意思是你不必强行用一条曲线穿过每个点：物理规律可能表明这是一个恒定值。

10. Final Revision Checklist | 最终复习清单

Use this checklist when practising old questions and comparing your answers with the mark scheme.

请在练习往年题目并结合评分方案批改时，使用以下清单。

Have I included the unit and the correct number of significant figures?

我是否写明了单位并使用正确的有效数字？
Have I used the command word to decide the amount of detail?

我是否根据指令词决定了作答的详细程度？
Have I shown the graph coordinates when calculating gradient?

计算斜率时，我是否写明了图线上的坐标点？
Have I drawn the line of best fit and the maximum/minimum gradient lines?

我是否画出了最佳拟合线以及最大/最小斜率线？
Have I used a table heading like ‘V / V’ rather than just a label?

表格标题是否写成“V / V”而不是简单写个名称？

The mark scheme is a map. If you learn its patterns, you can predict what examiners want before you start writing.

评分方案就像一张地图。如果你掌握了它的模式，就能在动笔之前预测考官想要什么答案。

Published by TutorHao | Physics Revision Series | aleveler.com

更多咨询请联系16621398022（同微信）

AQA A-Level Physics Unit 3 Mark Scheme (January 2022): Practical Skills and Exam Strategy | AQA A-Level 物理 Unit 3 评分方案（2022年1月）：实验技能与应试策略