Operational Amplifiers: Working Principles and Key Parameters | 运算放大器:工作原理与关键参数

📚 Operational Amplifiers: Working Principles and Key Parameters | 运算放大器:工作原理与关键参数

Operational amplifiers (op-amps) are fundamental building blocks in analogue electronics and a core topic in the CIE A-Level Physics syllabus. This article explains how op-amps work, the key parameters you must memorise, and how to analyse the three standard configurations: inverting, non-inverting and comparator circuits.

运算放大器(op-amp)是模拟电子学中的基本构件,也是 CIE A-Level 物理考纲中的核心专题。本文将讲解运算放大器的工作原理、必须牢记的关键参数,以及反相、同相和比较器三种标准电路的分析方法。


1. What Is an Operational Amplifier? | 什么是运算放大器?

An operational amplifier is a high-gain direct-coupled voltage amplifier with two inputs — one inverting (−) and one non-inverting (+) — and a single output. Its gain is so large that in most circuits negative feedback is used to control the overall behaviour.

运算放大器是一种高增益直流耦合电压放大器,具有两个输入端——一个反相端(−)和一个同相端(+)——以及一个输出端。其增益非常大,因此大多数电路中都要通过负反馈来控制整体行为。

  • Inverting input (−): a voltage applied here produces an output that is inverted (180° phase shift).

    反相输入端(−):在此处施加电压,输出端会产生反相(180° 相位差)的信号。

  • Non-inverting input (+): a voltage applied here produces an output that is in phase with the input.

    同相输入端(+):在此处施加电压,输出端会产生与输入同相的信号。

  • The op-amp is powered by dual supplies, typically +Vs and −Vs, and the output cannot exceed these supply rails.

    运算放大器通常采用双电源供电,即 +Vs 和 −Vs,输出电压不能超过这两个电源轨。


2. The Ideal Op-Amp Model | 理想运算放大器模型

CIE exam questions often begin with the ideal op-amp assumptions. You must know these four properties and use them in circuit analysis.

CIE 考试题通常从理想运算放大器的假设出发。你必须掌握这四个特性,并在电路分析中运用它们。

Property Ideal value Consequence
Open-loop voltage gain A₀ Infinity Even tiny input differences drive output to saturation
Input impedance Infinity No current flows into either input
Output impedance Zero Output voltage independent of load
Bandwidth Infinity Amplifies all frequencies equally

3. The “Golden Rule” — Virtual Earth | 黄金法则——虚地

When negative feedback is applied and the op-amp is not saturated, the output will adjust itself so that the voltage difference between the two inputs becomes zero. Since the non-inverting input is often connected to 0 V (earth), the inverting input is said to be at “virtual earth” — it is at 0 V but no current flows into it.

当施加负反馈且运算放大器未饱和时,输出会自动调整,使两个输入端之间的电压差变为零。由于同相输入端通常连接到 0 V(地),反相输入端便被称为处于”虚地”——它的电位是 0 V 但没有电流流入。

V₋ = V₊ (virtual short) and I₊ = I₋ = 0

This is the single most important rule for solving A-Level op-amp circuit problems. It allows you to write current equations at the inverting node as if it were a real earth.

这是解决 A-Level 运算放大器电路问题最重要的一条规则。它允许你将反相节点处的电流方程当作真的接地节点来书写。


4. The Inverting Amplifier | 反相放大器

The inverting amplifier is the most tested configuration in CIE A-Level Physics. The input signal is applied through resistor R₁ to the inverting input, and the feedback resistor R₂ is connected between the output and the inverting input. The non-inverting input is grounded.

反相放大器是 CIE A-Level 物理中考查最多的电路。输入信号通过电阻 R₁ 加到反相输入端,反馈电阻 R₂ 连接在输出端和反相输入端之间,同相输入端接地。

Using the virtual earth concept:

利用虚地概念:

Since V₋ = 0, the current through R₁ is I₁ = Vin / R₁. No current enters the op-amp, so the same current flows through R₂. Thus Vout = −I₁R₂ = −(Vin / R₁)R₂.

由于 V₋ = 0,通过 R₁ 的电流为 I₁ = Vin / R₁。没有电流进入运算放大器,因此同样的电流流过 R₂。于是 Vout = −(Vin / R₁)R₂。

Voltage gain = Vout / Vin = −R₂ / R₁

The negative sign indicates a 180° phase inversion. The gain depends only on the two resistors, not on the op-amp itself — this is the beauty of negative feedback.

负号表示产生了 180° 的相位反转。增益只取决于两个电阻的比值,而与运算放大器本身无关——这正是负反馈的妙处。


5. The Non-Inverting Amplifier | 同相放大器

In the non-inverting configuration, the input signal is connected directly to the non-inverting input (+), and the feedback network (R₁ and R₂) is connected between the output, the inverting input (−) and earth. The gain is always greater than or equal to 1.

在同相放大电路中,输入信号直接连接到同相输入端(+),反馈网络(R₁ 和 R₂)连接在输出端、反相输入端(−)和地之间。增益始终大于或等于 1。

Because V₊ = V₋ = Vin, the potential divider formed by R₁ and R₂ gives:

因为 V₊ = V₋ = Vin,由 R₁ 和 R₂ 构成的分压器给出:

Vin = Vout × R₁ / (R₁ + R₂)

Voltage gain = Vout / Vin = 1 + R₂ / R₁

Notice there is no minus sign — the output is in phase with the input. This circuit has a much higher input impedance than the inverting amplifier, because the signal sees the op-amp’s input directly.

注意这里没有负号——输出与输入同相。该电路的输入阻抗远高于反相放大器,因为信号直接进入运算放大器的输入端。


6. The Op-Amp as a Comparator | 运算放大器用作比较器

If no negative feedback is applied, the op-amp operates in open-loop mode and acts as a comparator. The output swings to either +Vs or −Vs (positive or negative saturation), depending on which input is at a higher potential.

如果未施加负反馈,运算放大器工作在开环模式,充当比较器。输出会摆向 +Vs 或 −Vs(正向或负向饱和),具体取决于哪个输入端的电位更高。

  • If V₊ > V₋, then Vout = +Vs (positive saturation).

    若 V₊ > V₋,则 Vout = +Vs(正向饱和)。

  • If V₊ < V₋, then Vout = −Vs (negative saturation).

    若 V₊ < V₋,则 Vout = −Vs(负向饱和)。

Comparators are used to convert analogue signals into digital logic levels, for example in temperature-sensing circuits where an LDR or thermistor forms part of a potential divider.

比较器常用于将模拟信号转换为数字逻辑电平,例如在温度传感电路中,光敏电阻或热敏电阻构成分压器的一部分。


7. Saturation and Output Limits | 饱和与输出限制

No real op-amp can output a voltage beyond its supply rails. When the required output exceeds the supply voltage, the op-amp “saturates” — the output stops changing and remains at approximately the supply voltage. In CIE questions, the maximum output is typically taken as the supply voltage Vs (sometimes slightly less).

真实的运算放大器不能输出超过其电源轨的电压。当所需的输出电压超过电源电压时,运算放大器会”饱和”——输出不再变化,而是保持在接近电源电压的数值。在 CIE 考题中,最大输出通常取为电源电压 Vs(有时略低)。

Saturation is a key exam trap: students calculate a gain and multiply it by Vin, obtaining a value like 15 V, but the supply is only ±9 V. The correct answer is +9 V (or −9 V), not 15 V.

饱和是考题中常见的陷阱:学生计算增益后乘以 Vin,得出 15 V 之类的结果,但电源只有 ±9 V。正确答案是 +9 V(或 −9 V),而不是 15 V。


8. Key Parameters: Gain, Bandwidth and Slew Rate | 关键参数:增益、带宽与压摆率

Beyond the ideal model, real op-amps have finite parameters that A-Level students should be able to interpret.

在理想模型之外,真实的运算放大器具有有限的参数,A-Level 学生应当能够理解这些参数的含义。

Parameter Definition Typical effect
Open-loop gain Gain without feedback, usually 10⁵–10⁶ Too high for linear use; needs feedback
Input impedance Resistance between inputs, typically MΩ or higher Prevents loading of the signal source
Output impedance Resistance seen at the output, typically < 100 Ω Allows driving external loads
Bandwidth Frequency range over which gain is constant Gain–bandwidth product is constant
Slew rate Maximum rate of change of output voltage (V/µs) Limits high-frequency large-signal performance

9. Negative Feedback and Its Benefits | 负反馈及其优点

Negative feedback is the secret behind the op-amp’s versatility. By feeding a fraction of the output back to the inverting input, the enormous open-loop gain is traded for predictable, stable behaviour.

负反馈是运算放大器多功能性的秘诀。将输出的一部分反馈到反相输入端,用巨大的开环增益换来了可预测、稳定的行为。

  • Gain is determined only by external resistors, so it is accurate and stable.

    增益仅由外部电阻决定,因此精确且稳定。

  • Bandwidth is increased compared to the open-loop configuration.

    与开环配置相比,带宽得到了扩展。

  • Distortion is reduced and the frequency response becomes more uniform.

    失真被减小,频率响应变得更加均匀。

  • The input–output relationship becomes linear over a wide range.

    输入与输出的关系在很大范围内呈现线性。

Vout = A₀(V₊ − V₋) — with feedback, A₀(V₊ − V₋) is forced toward the required Vout


10. Exam-Style Worked Example | 考试风格例题

An op-amp is connected as an inverting amplifier with R₁ = 2.0 kΩ and R₂ = 12 kΩ. The supply voltages are ±9 V. If Vin = +0.50 V, calculate Vout.

一个运算放大器连接成反相放大器,R₁ = 2.0 kΩ,R₂ = 12 kΩ,电源电压为 ±9 V。若 Vin = +0.50 V,求 Vout。

The theoretical gain is −R₂/R₁ = −12/2 = −6. Therefore Vout = −6 × 0.50 = −3.0 V. Since −3.0 V lies within the supply rails, no saturation occurs — the output is −3.0 V.

理论增益为 −R₂/R₁ = −12/2 = −6,因此 Vout = −6 × 0.50 = −3.0 V。由于 −3.0 V 在电源电压范围内,不会发生饱和——输出即为 −3.0 V。

If instead Vin = +2.5 V, the theoretical output is −15 V. But the supply is only ±9 V, so the actual output limits at −9 V (negative saturation). This example illustrates the importance of always checking saturation.

若改为 Vin = +2.5 V,理论输出为 −15 V。但电源只有 ±9 V,因此实际输出被限制在 −9 V(负向饱和)。这个例子说明了检查饱和的重要性。


11. Common Mistakes and Exam Tips | 常见错误与考试技巧

Students lose marks in op-amp questions for predictable reasons.

学生在运算放大器题目中失分的原因往往是可以预见的。

  • Forgetting virtual earth: V₋ is not exactly 0 V — it is forced to be equal to V₊. In a standard inverting amplifier this is 0 V, but the key is that no current flows into the input.

    忘记虚地:V₋ 并不是真正的 0 V——它被强制等于 V₊。在标准反相放大器中这个值是 0 V,但关键在于没有电流流入输入端。

  • Mixing up the gain formulas: inverting gain is −R₂/R₁, non-inverting gain is 1 + R₂/R₁. Never swap them.

    混淆增益公式:反相增益是 −R₂/R₁,同相增益是 1 + R₂/R₁。千万不要混淆。

  • Forgetting saturation: always check whether the calculated output exceeds the supply voltage.

    忘记饱和:务必检查计算得出的输出电压是否超过电源电压。

  • Ignoring input impedance: in a comparator, if both inputs are connected through resistors, use potential divider equations to find V₊ and V₋ first.

    忽略输入阻抗:在比较器中,如果两个输入端都通过电阻连接,先用分压公式求出 V₊ 和 V₋。

  • Writing units incorrectly: gain has no units, but Vout is in volts and currents are in amperes.

    单位书写错误:增益没有单位,Vout 的单位是伏特,电流的单位是安培。


12. Summary of Essential Equations | 必备公式小结

These are the only equations you need for CIE A-Level op-amp questions.

以下是 CIE A-Level 运算放大器题目中你唯一需要的公式。

Inverting amplifier: Vout = −(R₂ / R₁) Vin

Non-inverting amplifier: Vout = (1 + R₂ / R₁) Vin

Comparator: Vout = +Vs if V₊ > V₋, else Vout = −Vs

Open-loop gain: Vout = A₀(V₊ − V₋)

Master these, practise drawing the circuits from memory, and always check saturation before writing your final answer.

掌握这些公式,练习凭记忆画出电路图,并在写出最终答案之前始终检查是否饱和。

Published by TutorHao | Physics Revision Series | aleveler.com

更多咨询请联系16621398022(同微信)

📞 咨询 / 微信:16621398022(同微信)
A-Level / IGCSE / IB / AP 课程辅导 · 真题资料 · 留学申请规划
查看联系方式 →

Comments

屏轩国际教育cambridge primary/secondary checkpoint, cat4, ukiset,ukcat,igcse,alevel,PAT,STEP,MAT, ibdp,ap,ssat,sat,sat2课程辅导,国外大学本科硕士研究生博士课程论文辅导

This site uses Akismet to reduce spam. Learn how your comment data is processed.

咨询微信:16621398022(同微信) · 联系我们