CIE A-Level Physics: Equivalent Capacitance in Capacitor Networks | CIE A-Level 物理：电容器网络的等效电容分析

📚 CIE A-Level Physics: Equivalent Capacitance in Capacitor Networks | CIE A-Level 物理：电容器网络的等效电容分析

In CIE A-Level Physics, capacitors are often combined in series and parallel configurations within a single circuit. To analyse such networks, we replace the entire arrangement with a single equivalent capacitor whose effect on the circuit is identical. This article explains the rules for combining capacitors, the derivation of these rules, worked examples, and common pitfalls in examination questions.

在 CIE A-Level 物理中，电容器经常以串联和并联的组合方式出现在同一个电路中。为了分析这类网络，我们用单个等效电容器取代整个组合，使其对电路的作用完全相同。本文将解释电容器组合的规则、公式推导、典型例题以及考试中常见的易错点。

1. Why Equivalent Capacitance? | 为什么要计算等效电容？

When multiple capacitors are connected together, the voltage across each capacitor and the charge stored on each plate are not always obvious. Replacing the network with a single equivalent capacitor \( C_{\text{eq}} \) allows us to relate the total charge \( Q \) supplied by the battery to the terminal potential difference \( V \) through the simple equation \( Q = C_{\text{eq}} V \).

当多个电容器连接在一起时，每个电容器两端的电压以及每块极板上储存的电荷并不总是显而易见的。将网络替换为单个等效电容器 \( C_{\text{eq}} \)，我们就能通过简单的关系式 \( Q = C_{\text{eq}} V \) 将电池提供的总电荷 \( Q \) 与端电压 \( V \) 联系起来。

The key idea is that energy conservation and charge conservation must hold across the entire network. The equivalent capacitance is not obtained by simply adding or averaging values; we must derive it from the fundamental definitions.

关键在于，整个网络必须满足能量守恒与电荷守恒。等效电容并不是简单地把数值相加或求平均，而必须从基本定义出发进行推导。

2. Capacitors in Parallel: The Addition Rule | 并联电容器：相加规则

Consider two capacitors \( C_1 \) and \( C_2 \) connected in parallel across a battery of terminal voltage \( V \). In parallel, each capacitor experiences the same potential difference \( V \). The total charge supplied by the battery is the sum of the charges on each capacitor:

考虑两个电容器 \( C_1 \) 和 \( C_2 \) 并联在端电压为 \( V \) 的电池两端。在并联连接中，每个电容器承受相同的电势差 \( V \)。电池提供的总电荷等于每个电容器上电荷之和：

\( Q_{\text{total}} = Q_1 + Q_2 = C_1 V + C_2 V = (C_1 + C_2) V \)

Since \( Q_{\text{total}} = C_{\text{eq}} V \), we immediately obtain:

由于 \( Q_{\text{total}} = C_{\text{eq}} V \)，我们立即得到：

\( C_{\text{eq}} = C_1 + C_2 + C_3 + \cdots \)

Thus for parallel capacitors, the equivalent capacitance is simply the arithmetic sum of the individual capacitances. This is analogous to adding conductances in resistor networks.

因此，对于并联电容器，等效电容就是各个电容的算术和。这类似于电阻网络中电导的相加。

Key point: The voltage is the same across each parallel branch.
要点： 并联各支路两端的电压相同。
Key point: The total charge is the sum of individual charges.
要点： 总电荷等于各支路电荷之和。
Key point: For \( n \) identical capacitors each of value \( C \) in parallel, \( C_{\text{eq}} = nC \).
要点： 若 \( n \) 个阻值均为 \( C \) 的电容器并联，则 \( C_{\text{eq}} = nC \)。

3. Capacitors in Series: The Reciprocal Rule | 串联电容器：倒数规则

Now consider two capacitors \( C_1 \) and \( C_2 \) connected in series with a battery. In series, the same current flows through both capacitors during charging, so the magnitude of charge on each capacitor is identical: \( Q = Q_1 = Q_2 \). The total potential difference across the combination is the sum of the individual potential differences:

现在考虑两个电容器 \( C_1 \) 和 \( C_2 \) 与电池串联。在串联连接中，充电过程中通过两个电容器的电流相同，因此每个电容器上的电荷量大小相等：\( Q = Q_1 = Q_2 \)。组合两端的总电势差等于各个电势差之和：

\( V_{\text{total}} = V_1 + V_2 = \frac{Q}{C_1} + \frac{Q}{C_2} = Q\left(\frac{1}{C_1} + \frac{1}{C_2}\right) \)

Since \( V_{\text{total}} = Q / C_{\text{eq}} \), we have:

由于 \( V_{\text{total}} = Q / C_{\text{eq}} \)，我们有：

\( \frac{1}{C_{\text{eq}}} = \frac{1}{C_1} + \frac{1}{C_2} + \frac{1}{C_3} + \cdots \)

For two capacitors in series, this may be simplified to:

对于两个串联电容器，上式可简化为：

\( C_{\text{eq}} = \frac{C_1 C_2}{C_1 + C_2} \)

This reciprocal rule is the same in form as the rule for resistors in parallel. Note that the equivalent capacitance of a series combination is always smaller than the smallest individual capacitance.

这个倒数规则在形式上与电阻并联的规则相同。请注意，串联组合的等效电容总是小于其中最小的那个电容值。

Key point: In series, charge on each capacitor is identical.
要点： 串联时，每个电容器上的电荷相同。
Key point: The voltage divides inversely as the capacitance.
要点： 电压按电容的倒数分配。
Key point: For \( n \) identical capacitors each of value \( C \) in series, \( C_{\text{eq}} = C/n \).
要点： 若 \( n \) 个阻值均为 \( C \) 的电容器串联，则 \( C_{\text{eq}} = C/n \)。

4. Derivation for Two Capacitors in Series | 两个电容器串联的推导

Examiners often ask for the derivation of the series formula. Starting from Kirchhoff’s second law, the sum of the potential differences around the loop is zero. If the battery provides \( V \), then:

考官经常要求推导串联公式。从基尔霍夫第二定律出发，回路中电势差之和为零。若电池提供电压 \( V \)，则：

\( V – V_1 – V_2 = 0 \quad \Rightarrow \quad V = V_1 + V_2 \)

Using \( V = Q/C \) for each capacitor and noting that \( Q \) is the same:

对每个电容器使用 \( V = Q/C \)，并注意 \( Q \) 相同：

\( \frac{Q}{C_{\text{eq}}} = \frac{Q}{C_1} + \frac{Q}{C_2} \)

Dividing through by \( Q \) yields the reciprocal rule. The same derivation extends to three or more series capacitors.

两边除以 \( Q \) 即得倒数规则。同样的推导可推广到三个或更多串联电容器。

5. Mixed Networks: Step-by-Step Reduction | 混合网络：逐步化简法

For circuits containing both series and parallel sections, reduce the network stage by stage. Identify the simplest sub-group, replace it with its equivalent capacitance, and redraw the circuit. Repeat until a single capacitor remains. This is exactly analogous to simplifying resistor networks in current electricity.

对于同时包含串联和并联部分的电路，应分阶段逐步化简网络。找出最简单的子组，用其等效电容替换，然后重新绘制电路。重复这一过程，直到只剩下一个电容器。这与电流部分中化简电阻网络的方法完全类似。

Step 1: Look for capacitors directly parallel to each other — combine them by addition.
步骤1： 寻找彼此直接并联的电容器——用加法合并。
Step 2: Look for capacitors directly in series — combine them by the reciprocal rule.
步骤2： 寻找彼此直接串联的电容器——用倒数规则合并。
Step 3: Redraw the circuit after each reduction.
步骤3： 每次化简后重新绘制电路。
Step 4: Check whether the remaining capacitors are in series or parallel before the final combination.
步骤4： 最终合并前检查剩余电容器是串联还是并联。

A common mistake is to combine capacitors that do not have the same voltage (parallel) or the same charge (series). Always verify the connection before applying a formula.

一个常见错误是合并那些电压不相同（并联条件）或电荷不相同（串联条件）的电容器。在套用公式之前，务必确认连接方式。

6. Worked Example 1: Two Capacitors in Parallel | 例题1：两个电容器并联

A 2 µF capacitor and a 3 µF capacitor are connected in parallel across a 12 V supply. Find (a) the equivalent capacitance, (b) the charge stored on each capacitor, and (c) the total charge supplied.

一个 2 µF 电容器和一个 3 µF 电容器并联在 12 V 电源两端。求 (a) 等效电容；(b) 每个电容器上储存的电荷；(c) 电源提供的总电荷。

Solution:

解答：

(a) For parallel:

(a) 并联时：

\( C_{\text{eq}} = 2 + 3 = 5 \, \mu\text{F} \)

(b) Each capacitor has 12 V across it:

(b) 每个电容器两端电压均为 12 V：

\( Q_1 = 2 \times 10^{-6} \times 12 = 24 \, \mu\text{C} \)

\( Q_2 = 3 \times 10^{-6} \times 12 = 36 \, \mu\text{C} \)

\( Q_{\text{total}} = 24 + 36 = 60 \, \mu\text{C} \)

Alternatively, using \( Q = C_{\text{eq}} V = 5 \, \mu\text{F} \times 12 \, \text{V} = 60 \, \mu\text{C} \), which checks out.

或者利用 \( Q = C_{\text{eq}} V = 5 \, \mu\text{F} \times 12 \, \text{V} = 60 \, \mu\text{C} \)，结果一致。

7. Worked Example 2: Two Capacitors in Series | 例题2：两个电容器串联

A 6 µF capacitor and a 3 µF capacitor are connected in series across a 12 V supply. Find (a) the equivalent capacitance, (b) the charge on each capacitor, and (c) the voltage across each capacitor.

一个 6 µF 电容器和一个 3 µF 电容器串联在 12 V 电源两端。求 (a) 等效电容；(b) 每个电容器上的电荷；(c) 每个电容器两端的电压。

Solution:

解答：

(a) For series:

(a) 串联时：

\( \frac{1}{C_{\text{eq}}} = \frac{1}{6} + \frac{1}{3} = \frac{1}{6} + \frac{2}{6} = \frac{3}{6} \)

\( C_{\text{eq}} = 2 \, \mu\text{F} \)

(b) Charge on each capacitor is the same:

(b) 每个电容器上的电荷相同：

\( Q = C_{\text{eq}} V = 2 \times 10^{-6} \times 12 = 24 \, \mu\text{C} \)

\( V_1 = \frac{Q}{C_1} = \frac{24}{6} = 4 \, \text{V} \)

\( V_2 = \frac{Q}{C_2} = \frac{24}{3} = 8 \, \text{V} \)

Check: \( V_1 + V_2 = 4 + 8 = 12 \, \text{V} \). Note that the smaller capacitor has the larger voltage — voltage divides inversely with capacitance.

检验：\( V_1 + V_2 = 4 + 8 = 12 \, \text{V} \)。注意，电容较小的电容器承受的电压较大——电压按电容的倒数分配。

8. Worked Example 3: Mixed Network | 例题3：混合网络

Three capacitors are arranged as follows: \( C_1 = 4 \, \mu\text{F} \) and \( C_2 = 6 \, \mu\text{F} \) are in parallel, and this combination is in series with \( C_3 = 5 \, \mu\text{F} \). The network is connected to a 10 V battery. Find (a) the equivalent capacitance and (b) the charge on each capacitor.

三个电容器按如下方式连接：\( C_1 = 4 \, \mu\text{F} \) 和 \( C_2 = 6 \, \mu\text{F} \) 并联，该组合再与 \( C_3 = 5 \, \mu\text{F} \) 串联。网络接在 10 V 电池两端。求 (a) 等效电容；(b) 每个电容器上的电荷。

Solution:

解答：

(a) First combine \( C_1 \) and \( C_2 \) in parallel:

(a) 先将 \( C_1 \) 和 \( C_2 \) 并联：

\( C_{12} = 4 + 6 = 10 \, \mu\text{F} \)

This \( C_{12} \) is in series with \( C_3 = 5 \, \mu\text{F} \):

该 \( C_{12} \) 与 \( C_3 = 5 \, \mu\text{F} \) 串联：

\( \frac{1}{C_{\text{eq}}} = \frac{1}{10} + \frac{1}{5} = \frac{1}{10} + \frac{2}{10} = \frac{3}{10} \)

\( C_{\text{eq}} = \frac{10}{3} \, \mu\text{F} \approx 3.33 \, \mu\text{F} \)

(b) The total charge drawn from the battery:

(b) 电池提供的总电荷：

\( Q_{\text{total}} = C_{\text{eq}} V = \frac{10}{3} \times 10^{-6} \times 10 = \frac{100}{3} \, \mu\text{C} \approx 33.3 \, \mu\text{C} \)

For the series branch, \( C_3 \) and \( C_{12} \) carry the same charge \( Q = 33.3 \, \mu\text{C} \). For the parallel capacitors \( C_1 \) and \( C_2 \), the voltage across them is:

对于串联支路，\( C_3 \) 与 \( C_{12} \) 携带相同的电荷 \( Q = 33.3 \, \mu\text{C} \)。对于并联电容器 \( C_1 \) 和 \( C_2 \)，它们两端的电压为：

\( V_{12} = \frac{Q}{C_{12}} = \frac{33.3}{10} = 3.33 \, \text{V} \)

\( V_3 = \frac{Q}{C_3} = \frac{33.3}{5} = 6.67 \, \text{V} \)

Check: \( V_{12} + V_3 = 3.33 + 6.67 = 10 \, \text{V} \). Then:

检验：\( V_{12} + V_3 = 3.33 + 6.67 = 10 \, \text{V} \)。然后：

\( Q_1 = C_1 V_{12} = 4 \times 3.33 = 13.3 \, \mu\text{C} \)

\( Q_2 = C_2 V_{12} = 6 \times 3.33 = 20.0 \, \mu\text{C} \)

Check: \( Q_1 + Q_2 = 13.3 + 20.0 = 33.3 \, \mu\text{C} = Q_{\text{total}} \).

检验：\( Q_1 + Q_2 = 13.3 + 20.0 = 33.3 \, \mu\text{C} = Q_{\text{total}} \)。

9. Charge and Energy Distribution in Networks | 网络中的电荷与能量分配

In a series combination, the charge on every capacitor is identical, but the energy stored is \( \frac{1}{2} QV \), which depends on the voltage across each capacitor. Larger capacitances store more energy in parallel but less energy in series for the same applied voltage.

在串联组合中，每个电容器上的电荷相同，但储存的能量为 \( \frac{1}{2} QV \)，取决于每个电容器两端的电压。在相同外加电压下，较大的电容在并联时储存更多能量，而在串联时储存较少能量。

The total energy stored in the equivalent capacitor is equal to the sum of the energies stored in all individual capacitors, provided the network has been charged from an ideal source. This is a useful check for numerical answers.

只要网络由理想电源充电，等效电容器储存的总能量就等于所有电容器储存能量之和。这是检验数值答案的一个有用方法。

\( W_{\text{total}} = \frac{1}{2} C_{\text{eq}} V^2 = \sum \frac{1}{2} C_i V_i^2 \)

Note that if a charged capacitor is disconnected and then reconnected differently, energy may be lost as heat and the above equality may not hold.

注意，如果已充电的电容器被断开后以不同方式重新连接，能量可能以热量形式损失，上述等式可能不再成立。

10. Common Exam Pitfalls | 常见考试易错点

The following errors appear frequently in CIE examination responses:

以下是 CIE 考试答题中经常出现的错误：

Adding series capacitances directly: For series, you must add reciprocals, not the values themselves.
错误1：将串联电容直接相加： 对于串联，必须将倒数相加，而不是将电容值直接相加。
Assuming equal voltage across series capacitors: Voltage divides inversely with capacitance; only the charge is equal in series.
错误2：假设串联电容器电压相等： 电压按电容的倒数分配；串联中只有电荷相等。
Confusing with resistor rules: Capacitors in parallel add like resistors in series; capacitors in series add like resistors in parallel.
错误3：与电阻规则混淆： 电容并联的加法与电阻串联相同；电容串联的加法与电阻并联相同。
Unit errors: Always convert µF to F when using \( Q = CV \) in SI units, and check whether the answer requests µC or C.
错误4：单位错误： 使用 \( Q = CV \) 的 SI 单位时，务必把 µF 换算为 F，并检查答案是要求 µC 还是 C。
Ignoring the redrawing step: Failing to redraw after combining a sub-group leads to incorrect identification of subsequent connections.
错误5：省略重新绘制电路的步骤： 合并子组后不重新绘制电路，会导致后续连接方式的判断错误。

11. Symmetry and Special Cases | 对称性与特殊情况

In some networks, the circuit is symmetric with respect to the battery terminals. In such cases, the potential at the midpoint of two identical branches is the same. No current flows in a capacitor connected between two points of equal potential, so that capacitor may be ignored for the purpose of finding the equivalent capacitance.

在某些网络中，电路相对于电池两端具有对称性。在这种情况下，两条相同支路中点的电势相同。连接在两个等电势点之间的电容器中没有电流通过，因此在计算等效电容时可以忽略该电容器。

Another special case is the balanced Wheatstone-type capacitor network, though this is uncommon at A-Level. The standard procedure is always to combine series and parallel groups step by step, never to guess the result.

另一种特殊情况是平衡的惠斯通电桥型电容器网络，但在 A-Level 中并不常见。标准做法始终是逐步合并串联和并联组，切勿凭空猜测结果。

12. Practical Tips for Examination Questions | 考试答题实用建议

When faced with a capacitor network problem in the exam, adopt a systematic approach:

面对考试中的电容器网络问题时，应采用系统化的方法：

Read the circuit diagram carefully: Identify all nodes and label the capacitors with their values and units.
仔细阅读电路图： 找出所有节点，并标明每个电容器的数值和单位。
Start from the far end: Combine the sub-group farthest from the battery first, working back toward the terminals.
从远端开始： 先合并离电池最远的子组，再逐步向两端推进。
Use the charge-voltage tables: After finding \( C_{\text{eq}} \), work back to obtain \( Q \) and \( V \) for each capacitor, tracking all values in a table.
使用电荷-电压表： 求出 \( C_{\text{eq}} \) 后，反推每个电容器的 \( Q \) 和 \( V \)，并将所有数值记录在表格中。
Verify conservation laws: Check that series charges are equal and that voltages add to the supply voltage.
验证守恒定律： 检查串联电荷相等，且电压之和等于电源电压。

Configuration	Equivalent Capacitance	Charge	Voltage
Series	\( 1/C_{\text{eq}} = \sum 1/C_i \)	Equal on all	Divides inversely with C
Parallel	\( C_{\text{eq}} = \sum C_i \)	Divides proportionally with C	Equal on all

配置 | 等效电容 | 电荷 | 电压

串联 | \( 1/C_{\text{eq}} = \sum 1/C_i \) | 所有电容器相同 | 按电容倒数分配

并联 | \( C_{\text{eq}} = \sum C_i \) | 按电容正比分配 | 所有电容器相同

By mastering these rules and practicing step-by-step reductions, you will be well prepared for capacitor network questions in the CIE A-Level Physics examination.

掌握这些规则并练习逐步化简，你就能充分准备应对 CIE A-Level 物理考试中的电容器网络问题。

Published by TutorHao | Physics Revision Series | aleveler.com

更多咨询请联系16621398022（同微信）

CIE A-Level Physics: Equivalent Capacitance in Capacitor Networks | CIE A-Level 物理：电容器网络的等效电容分析